COMMUNIQUÉ DE PRESSE

Teng Yang Highlights Expanded DTF Transfer Film Options for Printing Businesses

Shanghai, China, November 17th, 2026, FinanceWire


Teng Yang (Shanghai Tengyang New Materials Technology Co., Ltd.), a hot melt adhesive manufacturer, is highlighting its DTF transfer film range for print shops and distributors, offering customizable PET film solutions in different thicknesses, widths, and formats, with both hot-peel and cold-peel options.

The company's DTF transfer film range includes coated polyester carriers supplied in bulk rolls or custom-cut sheets, designed to meet different printing and production requirements. Through its existing product offering, Teng Yang provides options for businesses looking to match film specifications to their printer feed widths, production volumes, and heat-press workflows.

Selecting the right film specification can help print shops avoid common production issues, including incorrect roll widths, unsuitable peel modes, and inconsistent coating performance. The company provides product specifications and customization options to help buyers evaluate film compatibility before changing suppliers.

What DTF transfer film does in the print-to-garment sequence

Direct-to-film printing puts the design on a coated PET carrier instead of on the garment. CMYK color is printed over a white ink base. Hot-melt powder goes onto the wet ink, the sheet is cured, and the finished transfer is heat-pressed onto fabric before the film is peeled away. On the company's DTF materials page, PET film thickness is listed as 75–100 µm, described as running from flexible to roll-stable.

Because of that white base, one roll can serve dark and light garments, cotton and poly-blends. Ink, powder and film behave as one system, so a change to any one of them can show up as edge bleed, poor release or a weak bond after washing.

Where it stops: the base PET is not what holds the ink. According to Teng Yang's product page, ink lock-in and peel behavior come from the coating step, not from the polyester substrate. Two films with the same thickness label can print and release differently, so a quote compared on thickness alone compares the wrong attribute.

Why short runs moved print shops toward film

Screen printing needs a separate plate for each color. The heat transfer PET film page states that on short runs of 5 to 200 items, plate setup costs outweigh production savings. Film removes the plate step, so a five-color design costs the same setup effort as a one-color design.

 The same page notes that a 20-piece, multi-color order and a 2,000-piece production run use the exact same roll. One film specification can therefore cover sampling, reorders and seasonal peaks. Qualification matters more, because a single approved roll now carries most of the shop's output.

Where it stops: the company says plainly that film is not always cheaper per piece than screen printing on very large runs. Film wins in the short-run band; above it, compare actual cost per finished garment, reprints included.

Hot-peel and cold-peel are production choices, not quality grades

Buyers often ask which peel mode is better. The company's answer is that the question is framed wrongly: peel mode should follow the press routine and the finish the shop wants, and both are stocked so that no shop is forced into one. Below is a summary of the differences described on its product page.

Point of comparisonHot-peel filmCold-peel film When the film comes offImmediately after pressing, while still warmAfter the transfer cools fully to room temperature Line paceFaster cycle for batch runsSlower cycle, with a cooling step inside the line Common finishFirm bond; some inks read slightly glossierOften more matte, closer to the fabric hand Best-fit workSame-day batches and time-pressured ordersDetail-heavy designs and soft hand-feel On that page the engineering team puts it directly: “Buyers ask us to just pick a peel mode for them, and honestly we can’t, it depends on what’s running through their press that week. A shop doing same-day rush orders and a shop doing detail-heavy one-offs shouldn’t be buying the same film.”

Finish is not fixed by the film either. Press temperature, dwell time and ink move the result as much as the coating does, which is why shops disagree about which mode looks more matte. Many run a warm peel, a short hold rather than a full cool-down, and a buyer leaning that way should say so when asking for a quote.

What 75μm and 75–100 µm mean on the press

Teng Yang engineers its film in-house to a common single-side-coated thickness of roughly 75μm. Its DTF materials overview gives the wider band: thinner film feeds easily through desktop and converted printers, while heavier film stays flat on large designs and long rolls. Thickness is a handling decision first.

 Thin-film properties have an established test route. Instron's guide to ASTM D882 explains that the method covers plastics less than 1 mm thick and expects specimens to be uniform to within 10% of the thickness between the grips. Film in this class sits far inside that scope, so a buyer can ask which tensile and thickness checks back the figure on the label rather than accepting a single nominal number.

Where it stops: tensile data describes the polyester carrier. How the release coating behaves in a heat press is a separate question, so a thickness certificate never replaces a print-and-press trial on the shop's own printer, powder and fabric.

Roll width and format: the most common ordering mistake

New accounts most often get the roll size wrong. Ordering DTF transfer film in a width that does not match the printer feed leads to jams or a wasted stripe of film on every pass, and the loss compounds at production volume. Standard roll widths for this film class run from about 30cm to 120cm. Teng Yang asks for the printer's actual feed width rather than a nominal model size, and produces width, length and thickness to order.

 Format follows volume. Rolls suit continuous production on roll-fed printers, while A4/A3 sheets suit small batches, pilot runs and shops with limited storage. Distributors reselling under their own label can order private-label packaging alongside standard sizes.

Ink, powder and press settings decide whether a new roll fits the line

A transfer film is one part of a three-part kit with the ink and the hot-melt powder. When a shop swaps only the film, the real question is whether the new roll behaves with the printer and powder already in use. The company builds its DTF PET film for mainstream CMYK-plus-white printers and the most common hot-melt powders, and asks for setup details up front so that an unusual recipe is caught before a production run.

For orientation, its DTF materials page lists an industry-typical transfer press setting of about 150–165 °C for 10–15 seconds, with the lower end used to protect polyester from dye migration. These are labeled as reference values that vary by supplier and grade, and grade-specific values are issued with each order.

Coating drift and the limits of a sample roll

Coating drift is the risk buyers rarely ask about. A release layer can look fine on the first meter of a roll and start causing peel problems by the last. Teng Yang's answer is structural: casting, coating, slitting, and rewinding run on the same core production floor that serves its hot melt adhesive film lines, rather than rolls being relabeled from an outside mill.

A sample proves less than buyers assume. One length of film printing and releasing well on one day says nothing about roll-to-roll consistency, or about how the coating holds up after weeks in a humid store room. The company advises keeping rolls and sheets dry, at moderate temperature and out of direct sunlight, because the release layer can drift if it absorbs moisture before printing. Test the first and last meters of a trial roll, and repeat the check on the first production delivery.

What to settle before requesting a DTF transfer film quotation

Buyers who bring these decisions to the first enquiry remove the usual causes of returned or wasted film, and Teng Yang asks for the same points before quoting:

  • State the printer's real feed width, and whether it is roll-fed or sheet-fed.
  • Choose hot-peel or cold-peel, or ask the supplier to advise against your press routine.
  • Give the expected monthly volume and the preferred format, roll or sheet.
  • Name the ink, the powder grade and the curing method: conveyor oven, heat press or sheet oven.
  • Specify any private-label packaging or custom roll length before sampling begins.
  • Agree how the first and last meters of the trial roll will be checked and recorded.

None of these steps proves that a film suits every garment. They make a trial comparable, so a later reorder refers to the same film, coating and settings that passed.

About Shanghai Tengyang New Materials Technology Co., Ltd.

Shanghai Tengyang New Materials Technology Co., Ltd., which sells under the Teng Yang name, is a hot melt adhesive manufacturer based in Shanghai, China, and a wholly owned subsidiary of Shanghai Hengning New Materials Co., Ltd. Its range covers hot melt adhesive films, webs, powders and granules in TPU, EVA, PA, PES and PO chemistries, together with DTF transfer materials for heat-transfer printing, for buyers in garment, footwear, automotive interior and packaging manufacturing.

Print shops and distributors comparing film formats can review Teng Yang's hot melt adhesive and DTF transfer materials range. Betty Fang is the listed company contact at Betty@hotmeltmaterial.com. Its address is on Fumin Branch Road, Hengsha Township, Chongming District, Shanghai, China.



Contact
Betty Fang
Shanghai Tengyang New Materials Technology Co., Ltd.
Betty@hotmeltmaterial.com
+86 13122233268


Disclaimer. This is a paid press release.